Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Mr-Glass Construction in Perris, CA | Iron Beam Contractors
We install, service, and repair Mr-Glass shower enclosures across Perris as an independent contractor crew, not a manufacturer affiliate. Most Perris call-outs come down to one thing: the valley’s dust, hard water, and tract-grade framing beating up hardware that was never spec’d for this environment. If your Mr-Glass door is stiff, leaking, or racked, call (833) 756-5936 and we’ll tell you whether it’s a repair or a replacement before you spend a dollar.
Why Perris Residents Choose Us for Mr-Glass Service
We’ve pulled Mr-Glass panels out of 1990s stucco tract homes off the I-215 and out of older ranch-style houses in 92570. That range matters. The same Mr-Glass frameless slider behaves differently in a 2004 subdivision than it does on a former citrus parcel, and we’ve learned both failure patterns the hard way. Nolan Driscoll, our owner, grew up on Orange County’s clay and spent two decades framing and reinforcing before Iron Beam ever hung its first glass panel. His rule: know what’s in the wall before you open it, not after. That’s why our Mr-Glass work starts with the opening, not the glass.
We carry OEM Mr-Glass rollers, hinges, seals, and sweeps where they’re still available. When OEM parts are discontinued or priced past what makes sense, we say so and offer proven aftermarket equivalents. You’ll always know which one you’re getting. We’re independent, so there’s no corporate script to follow, just the truth about your enclosure.
Styles & brands we work with







Common Mr-Glass Construction Problems We Solve in Perris
- Grit-packed bottom tracks and rollers. Perris Valley wind pushes fine dust straight into the bottom track of framed sliding Mr-Glass doors. The rollers stiffen, then start scratching the coated glass every time the door moves. We pull the track, clean or replace the rollers, and re-set the door so it glides instead of grinding.
- Hard water scaling and etched glass. Perris fill water is mineral-heavy, and it shows up as white scaling on Mr-Glass panels and pitting on hinge and seal hardware. We remove what can be removed, polish where polishing still works, and tell you plainly when the glass is etched past saving.
- Racked panels from out-of-plumb tract framing. Newer subdivisions east and west of the I-215 were built fast. Greenboard and cheap framing twist over time, and the Mr-Glass door no longer seats or sweeps cleanly. We true the jamb and curb, then re-hang the panel.
- UV-dried seals and sweeps. Perris summers bake clear seals until they yellow, crack, and let water leak onto stucco walls and wood subfloor near the curb. We replace seals and sweeps before the leak becomes a rot problem.
- Track and curb settlement on former Ag ground. In the Perris Valley, former agricultural parcels hide old irrigation lines, fill dirt, and buried debris that were never on any tract map. Curb settlement racks Mr-Glass panels. We re-level and re-set the opening, then re-hang the enclosure.
Mr-Glass Service in Perris: What Local Conditions Mean for Your Equipment
Perris is one of the fastest-growing cities in Riverside County, and much of the new construction here sits on former agricultural land at the foot of the Perris Valley. That’s not a zoning footnote; it’s a daily reality for the work. We regularly open walls in Perris to find old irrigation lines, unrecorded fill, and buried debris that no map shows. When a Mr-Glass shower opening is out of level because the curb settled over a pocket of uncompacted fill, the door racks, the sweep fails, and water finds the floor. We’ve had to re-set and re-level shower curbs mid-project more times in Perris than anywhere else we work. That extra step is exactly what keeps a Mr-Glass panel true for the next decade instead of the next season. In the newer subdivisions east of the I-215, the framing itself is often the culprit. We were called to a tract home there because a builder-grade semi-frameless Mr-Glass slider kept jumping its track and leaking. Pulling the door showed the wall opening was nearly half an inch out of plumb from the original framing. We trued the curb and jambs, replaced the worn rollers and sweep with OEM Mr-Glass hardware, and re-hung the panels. No more leaks, and the door glides again. That’s the difference between trusting the as-built framing and actually checking it.
Mr-Glass Models & Products We Service in Perris
We work across the Mr-Glass lineup: frameless sliding shower door systems in the Excel and Elite-style series, semi-frameless pivot enclosures, custom neo-angle and corner units, and tub-shower combination sliding doors. The repair approach is the same on every model: match OEM hardware where it’s still available, switch to quality aftermarket equivalents when OEM is discontinued, and always tell you which. If the glass is solid and only rollers, hinges, or seals have failed, we repair. If the panel is chipped, etched past polishing, or the opening has racked, we say so and walk you through replacement. For Perris turnaround, we keep common Mr-Glass rollers, sweeps, and seals on hand so a one-visit fix is the norm, not the exception.
See the difference
Before
After
Before
After
Before
AfterMr-Glass Service Pricing in Perris
What you’ll pay depends on what failed. Hardware-only repairs on Mr-Glass doors run on the lower end. Full enclosure replacement or a racked opening that needs re-framing runs higher. Here’s what we see in Perris:
| Service | Typical Range |
|---|---|
| Frameless Glass Shower Enclosure | $4,500 – $12,000 |
| Walk-In Shower Installation | $4,500 – $12,000 |
| Tub-to-Shower Conversion | $3,500 – $10,000 |
| Shower Replacement | $3,000 – $8,500 |
Your free estimate includes an on-site check of the opening, the track, the hardware, and the seals, plus a written line-item price for exactly what we’d do. Call (833) 756-5936 to schedule one. You’ll know the number before you commit to anything.
Serving Perris, CA — Our Local Coverage Area
We’re based in the Perris area and know this community well. Use the map below to see our service coverage — if you’re nearby, we can almost certainly help.
FAQs – Mr-Glass Construction in Perris
No. Iron Beam Contractors is an independent general contractor. We are not affiliated with, authorized by, or endorsed by Mr-Glass. We service their enclosures because we’ve worked on them for years across Perris and know how they hold up here. That independence means we tell you the truth about parts and pricing without a corporate script.
Yes, it does. Perris Valley heat cycles dry out and yellow the clear seals and sweeps, and wind-driven dust packs the bottom tracks and roller channels. We see it most on framed sliders on ground-level homes near open graded lots. Replacing seals and rollers before water leaks into the wall is the cheapest fix in the long run. Call (833) 756-5936 for an inspection and exact quote, the estimate is free.
Both, and we tell you which every time. OEM Mr-Glass rollers, hinges, seals, and sweeps are our first choice while they’re available. When OEM parts are discontinued or priced past reason, we use proven aftermarket equivalents that match the hardware spec. You always know what’s going on your shower.
Most hardware-only repairs are done in one visit. A full enclosure replacement or a job where the opening has racked and needs re-framing typically runs two to three working days, depending on what’s behind the wall. We won’t give you a vague window; we’ll give you a schedule after we see the opening.
Frameless sliding shower door systems in the Excel and Elite-style series, semi-frameless pivot enclosures, custom neo-angle and corner units, and tub-shower combination sliding doors. If you have a photo and a rough measurement, we can usually tell you over the phone whether it’s a repair or a replacement before we even come out.
Service Areas Near Perris
Our Mr-Glass service coverage extends beyond Perris into neighboring communities across Riverside and Orange counties. We handle enclosures in Mr-Glass service in Moreno Valley for tract homes with the same framing issues we see east of the I-215, and Mr-Glass service in Colton for older housing stock that needs different wall-opening work. Full coverage details are on our Perris service area page and our Mr-Glass sales & service page.
Book Your Mr-Glass Service in Perris Today
If your Mr-Glass door is grinding, leaking, or sitting crooked in the opening, don’t let the next Perris wind storm make it worse. Call (833) 756-5936 for a free estimate. We’ll tell you what’s wrong, what it costs, and whether it’s a repair or a replacement.
Written by Nolan Driscoll, Owner at Iron Beam Contractors, serving Perris and the surrounding valley.